Each person will have his or her own thinking when it comes to How to Install a Bathtub Yourself.
Mounting a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old tub with a brand-new one is additionally a reasonably tough job. If the old bathtub is easily available, the task can move immediately; if you need to open a wall to get rid of the old bathtub and also position the brand-new bathtub, the task is much harder. In either case, the project is within a residence handyman's skills, although you will need an assistant to vacate the old bathtub as well as embeded in the brand-new one. Make certain you have certified on your own for the job as well as are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed project, it is better to take into consideration utilizing one before you start. Opportunities are you may need an expert plumber to make tube links.
This article will certainly aid you mount a new bathtub in your washroom if you have actually already bought a new bathtub and also do not need to change the setup of your previous water pipelines.
Your devices as well as material list must make up the following:
Preparing for the Installment
To start with, the supporting framework provided with the bathroom should be fitted (if required) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to see to it that if the tap features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps system to prevent stress on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps utilizing 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be suited its final setting.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is disconnect the water. After doing so, turn on the faucets to drain any type of water staying in the system. The procedure of eliminating the existing taps can be quite troublesome because of the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a fabric ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been gotten rid of, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from transforming during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Before carrying on to fit the new faucets, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Using the two wood boards under its feet, place the bathtub in the needed setting. The wood boards are valuable in equally spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small points.
The next objective is to make sure that the tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bathtub until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest adaptable tap connector to the proper supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Activate the water supply and check all joints and also new pipework for leaks and tighten them if needed. Load the bath tub and also inspect the overflow outlet and the normal outlet for leakages.
Finally, deal with the bath paneling as explained in the maker's instruction manual. Tiling and also sealing around the bathtub should wait up until the bathtub has been utilized at the very least when as this will settle it right into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the tap and also the sink. Protect the faucet in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet adapters. The former kind should be linked to the faucet ends initially, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to fracture a stiff seal, causing the water to pass through the wall in between the bathroom as well as the tiling, bring about difficulties with dampness and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly load the tub with water prior to sealing, to enable the motion experienced when the tub is in use. The sealant can crack fairly very early if you do not think about this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is advisable to fit the ceramic tiles using water-resistant or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading about How to Install a Bathtub? Put a remark down the page. We'd be interested to find out your insights about this blog entry. We hope that you come back again before long. Remember to take the time to distribute this post if you appreciated it. Thanks for going through it.
Quick, quality, call!